How to Prepare the Ground for a Resin Driveway

Posted on: July 23, 2022

The first step in laying a resin driveway is to prepare the ground. A good ratio of 7% is important for a strong mix. Sand should be at least 18mm thick. Resin is laid to a depth of 12mm, but may be thicker. Using a float trowel, smooth the mixture out with a clean surface. The resin is ready to be walked on after four hours. If the ground is spongy or wet, it may need to be removed and reapplied.

Requires a minimum of 18mm depth

If you are going to install a resin driveway, it’s vital that you choose a professional installer. In order to prevent mistakes, you should ensure that the thickness of the resin driveway is as close to three times the largest size of aggregate as possible. In general, the recommended depth for a resin driveway is 18mm. Otherwise, the surface can rip and crack, which will require a large amount of money to fix.

A sub-base is a necessary part of installing a resin driveway. If you’re installing one on top of block paving, you’ll need to dig out the old driveway to make room for the new one. If you’re installing one on top of an existing concrete sub-base, you’ll need a minimum of six inches of MOT or base coat tarmac. Make sure that you have a solid sub-base when you ask your installer about this.

A minimum of 18mm depth is necessary to ensure a solid base for the resin-bound driveway. The installation process is a straightforward process, but you must remember that it may take a couple of days to cure. If you’re installing a new resin driveway, you should always allow enough time for the material to cure before allowing foot or vehicle traffic. Ideally, you should leave at least 12 hours for resin driveways to cure completely. However, this can be longer if it’s the case that the resin bound driveway is not cured.

Requires a minimum of 7% ratio

If you want a beautiful and long-lasting resin driveway, you’ll need to follow the steps below to get started. First, remove the old surface, such as flags, block paving, or soil. Next, lay a new concrete foundation on top of the existing driveway. Then, apply a mixture of sand, cement, and resin at a ratio of 7:1. The mix must be thick enough to form a strong, stable, and water-resistant surface. Be sure to level the driveway first, with the edging being raised between 15-20mm and the existing surface.

Having a solid resin drive requires a proper sub-base. Concrete slabs can shift due to base movement. When temperatures rise, asphalt can warm up and cause base movement. Similarly, if compaction ratings are too low, sub-base settlement may occur. This can lead to cracks in the resin driveway. Fortunately, a resin driveway can be repaired with a supplementary layer.

When laying a resin driveway, it is crucial to prime the surface with a primer. Do not use too thick of a primer, as it can interfere with the resin’s adhesion. Also, be sure to keep the resin from getting too wet, as it can weaken the layers and compromise the final finish. A resin driveway will also cure too quickly if it is exposed to too much heat. If possible, lay the resin early in the morning or outside of the hottest times of the day. You can also monitor surface temperature with a thermometer and make necessary adjustments.

Easy to maintain

The first step to building a resin driveway is preparing the ground for the installation of the surface. As a seamless surface, the sub-surface must be in good condition. After preparing the ground for resin driveway installation, inspect it for damage caused by the driveway’s previous layer. The sub-base should be stable and firm and must support the expected weight of the resin driveway. Clean and dry surfaces are also essential. Measure the temperature and humidity of the surface before laying the driveway.

If you have a resin bound driveway, tyre marks can leave unsightly marks. This happens because the heat generated by the tyres interacts with the resin, making it more prone to tyre marks. If you notice a tyre mark, wipe it off with soap and water. Avoid stepping on the resin driveway if the area is wet, as this can break it down and cause a hole in the surface.

Despite the low maintenance requirement, a resin driveway still requires a little care. The surface must be protected from hard objects, such as car parts, garden machinery, plant pots, seating, and other similar objects. Hard objects, like gravel, can get stuck between the treads of tyres, causing marks and scratches on the surface. Therefore, if you are adamant about the appearance of your driveway, make sure it is free of gravel.